Icynene Insulation Removal in Dallas: What to Know First
Icynene insulation removal in Dallas typically runs $1.50 to $3.50 per square foot depending on the product type, attic access, and how much material needs to come out. Most jobs are completed in one day, and we give you a written price before any tool comes off the truck. This page is for Dallas homeowners who have Icynene spray foam or injection foam that’s failed, been damaged by pests or moisture, or needs to come out before a remodel or re-insulation. Call (940) 748-1726 for a free estimate.
We’re Alden Insulation Dallas, an independent Icynene service provider. We are not a franchise, not a corporate branch, and not affiliated with or authorized by Icynene. We’re a local Dallas crew, part of the Garrison Partners family since 2002, held to The Garrison Standard: written prices, written guarantees, and background-checked techs who show up inside the window they promised. Bryce Holloway runs our Dallas operation, and he’s the one who makes sure your removal job gets done right.
How Icynene Products Fail – and How We Fix Them
Every spray foam brand has its own weak points, and Icynene is no exception. Here’s what we see on Dallas jobs:
- Icynene Classic (open-cell) shrink lines. Classic is a light-density open-cell foam. In Dallas attics, where summer heat bakes roof decks for months, we see early batches pull away from rafters and leave hairline gaps. Air finds those gaps. If your Classic has separated from the decking, removal is usually the cleanest fix before re-insulating.
- Icynene ProSeal (closed-cell) moisture trapping. ProSeal is a closed-cell foam, which means it doesn’t breathe. If a roof leak or plumbing leak sat on it, moisture gets trapped against the sheathing. You won’t see it until the drywall stains below. That foam has to come out before the framing can dry and we can air-seal properly.
- Icynene Lite (injection foam) settling in wall cavities. In older Dallas homes, especially around Lakewood where we’ve done quite a few jobs, injection foam shrinks over time and settles. You end up with uninsulated bands at the top of wall cavities. Removal in tight wall cavities is slow work, but if it’s done, it’s done right.
- Off-ratio installs from the original builder. Some Dallas production homes got Icynene applied by a crew running the rig too hot or too cold. The foam cures powdery, crumbly, or with a persistent amine smell. We get calls for this after homeowners have lived with it for years. Removal of off-ratio foam is straightforward, but it’s messy, so we lay down full containment before cutting into it.
- Rodent and pest damage. Rats and squirrels tunnel through open-cell Icynene like it’s a hotel. Once the foam is chewed up, its R-value is gone and the material is contaminated. We remove the damaged sections, and we’ll tell you honestly whether the rest is still sound or needs to come out too.
Our Icynene Insulation Removal Process
- 1
Call and schedule. A live person answers, 24/7. We set a date and a window. We arrive inside that window, in uniform, ready to work.
- 2
Attic assessment. We inspect the foam: product type, depth, adhesion, moisture readings, and any pest or thermal damage. We measure square footage and note access limitations. If you have a blower-door number from a previous audit, we want to see it.
- 3
Written price. Before anything gets touched, you get the number in writing. It covers labor, containment, removal, bagging, and disposal. The number you approve is the number on the invoice. No surprises.
- 4
Containment and removal. We set up dust containment around the attic access, then cut, scrape, and bag the Icynene. Closed-cell foam is harder to remove than open-cell and takes longer, so we plan for that. We don’t rush it, and we don’t leave it half-done.
- 5
Cleanup and salvage check. We vacuum the attic floor, check for nails and debris, and make sure the space is ready for whatever comes next – new insulation, air sealing, or just a dry, empty attic. If we spot framing damage from trapped moisture, we’ll tell you what we found and who should look at it.
- 6
365-Day Done Right Promise. Every job gets a written guarantee. If the removal work fails within a year, we come back and make it right at no charge. That’s The Garrison Standard, and we don’t make exceptions.
What Icynene Insulation Removal Costs in Dallas
The honest price range is $1.50 to $3.50 per square foot. Open-cell Icynene like Classic removes faster and lands at the lower end. Closed-cell ProSeal takes more labor and materials, so it runs higher. Wall cavity injection foam is the most expensive to remove, because the access is slow and the material doesn’t let go easily.
What moves the price:
- Product type: Closed-cell costs more than open-cell to remove.
- Access: Tight attics, low slopes, or finished ceilings below the foam add labor.
- Contamination: Pest damage or long-term moisture means more containment and slower work.
- Scope: Full removal costs more than section removal. We’ll tell you if you’re a candidate for a partial fix instead of a full pull.
Every job starts with a free estimate. Call (940) 748-1726 and we’ll walk the attic, measure, and put a written number in your hand.
Why Dallas Homeowners Call Alden Insulation Dallas for Icynene Work
A lot of Dallas insulation contractors will remove foam, but not many will put a 365-day written guarantee on the work. We do. We also name the products we work with – Icynene, Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Demilec, GreenFiber, and Reflectix for reflective applications – so you can look them up before you commit. We’re independently owned and operated, held to The Garrison Standard. That means the crew shows up when we said they would, the price doesn’t move at the door, and the technician in your attic passed a background check before he ever set foot in your home.
Bryce Holloway grew up in Los Angeles and learned insulation at Los Angeles Trade-Technical College, then spent two decades doing this work full time. He’s run Dallas jobs from Lakewood to the northern suburbs, and he’s seen what older Texas attics do to foam that wasn’t applied right. Get the R-value right, and the house takes care of the rest. That’s how we approach every removal, because a clean removal sets the stage for a clean install.
FAQs
Usually not. Most removal jobs need containment set up and a schedule blocked out, so we typically run removal within one to three days of the estimate depending on the scope. Call (940) 748-1726 and we’ll give you a straight answer.
If your Icynene is still under manufacturer warranty, removing it yourself will void that warranty. We recommend calling Icynene first. As an independent Icynene service provider, we can’t act on their behalf, but we can document the failure with photos and moisture readings to support your case, and remove it if the warranty process doesn’t work out.
It depends on what’s wrong. If the foam is sound and just underperforming, we might recommend air sealing and adding material over it. But if the Icynene is contaminated, crumbling, or holding moisture, covering it only hides the problem. We’ll tell you which camp you’re in before you spend a dollar.
No. Wall cavity injection foam like Icynene Lite requires either opening the wall or pulling the foam through existing access points. It’s slower and more labor-intensive than attic removal, which is why it lands at the higher end of the price range. We’ll explain exactly what your walls need before we quote it.
If you’ve had a roof leak or a pest infestation and the foam is actively causing damage, call (940) 748-1726. We answer 24/7, and in an emergency we can often get a technician out the same day in the Dallas area to at least stop the bleeding and set up containment.
Call Alden Insulation Dallas for Icynene Insulation Removal
If you’re a Dallas homeowner with Icynene that’s failed, been destroyed by pests, or needs to come out before your next insulation install, call (940) 748-1726 for a free estimate. We show up on time, price the job in writing before we start, and back the work with a 365-day guarantee. That’s what you’re paying for, and that’s what you’ll get.
Written by Bryce Holloway, Owner, Alden Insulation Dallas at Alden Insulation Dallas, serving Dallas and nearby areas.